![]() |
|||
![]() |
|||
![]() |
![]() |
|||
![]() |
|||
![]() |
High Performance Magnetic Flux Vector Miniaturization Generic Inverter.
High Performance Generic Inverter.
Characteristic
Built-in PI control
Restart/Free run start
PWN frequency 1.5~10KHz
Output frequency 0.5~240.0Hz
10 pattern and any V/F pattern
8-step speed setting
2-step acceleration/deceleration
Parameter input by key number 0~9
External analog setting 0~10V and 4~20mA
Automatic torque compensation and slip compensation
Frequency increase/decrease(UP / DOWN)function and 16-step function control setting
A. 200V 3 phase
Motor rating (KW) |
2.2 |
3.7 |
5.5 |
7.5 |
11 |
15 |
18.5 |
22 |
30 |
37 |
45 |
55 |
75 |
93 |
112 |
131 |
150 |
Model CT2002F- |
2A2 |
3A7 |
5A5 |
7A5 |
011 |
015 |
18A5 |
022 |
030 |
037 |
045 |
055 |
075 |
093 |
112 |
131 |
150 |
Rated current (A) |
11.1 |
18 |
23 |
33 |
48 |
61 |
75 |
86 |
125 |
150 |
170 |
210 |
278 |
330 |
390 |
440 |
500 |
Rated capacity (KVA) |
4.4 |
7.1 |
9.2 |
13.1 |
19.1 |
24.3 |
29.9 |
34.3 |
49 |
60 |
68 |
84 |
111 |
131 |
156 |
175 |
199 |
Power supply | 3∮ 200~230V ±10% , 50Hz/60Hz ±5% | ||||||||||||||||
Output voltage | 3∮ 200V, 220V, 230V | ||||||||||||||||
Cooling system | Forced air-cooling | ||||||||||||||||
Weight (Kg) |
8 |
8 |
9 |
14 |
14 |
20 |
20 |
30 |
45 |
60 |
60 |
65 |
70 |
70 |
70 |
123 |
123 |
B. 400V series
Motor rating (KW) |
3.7 |
5.5 |
7.5 |
11 |
15 |
18.5 |
22 |
25 |
30 |
37 |
45 |
55 |
75 |
93 |
112 |
132 |
150 |
187 |
225 |
262 |
300 |
Model CT2004F- |
3A7 |
5A5 |
7A5 |
011 |
015 |
18A5 |
022 |
025 |
030 |
037 |
045 |
055 |
075 |
093 |
112 |
132 |
150 |
187 |
225 |
262 |
300 |
Rated current (A) |
9 |
13 |
17.3 |
24 |
31 |
38 |
52 |
61 |
65 |
71 |
93 |
110 |
156 |
180 |
225 |
260 |
290 |
370 |
460 |
530 |
610 |
Rated capacity (KVA) |
7.1 |
10.4 |
13.8 |
19.1 |
24.7 |
30.3 |
41.4 |
47.1 |
51.8 |
56.6 |
74 |
87.6 |
124 |
143 |
180 |
206 |
230 |
293 |
364 |
419 |
485 |
Power supply | 3∮ 380~460V ±10% , 50Hz/60Hz ±5% | ||||||||||||||||||||
Output voltage | 3∮ 380V, 400V, 440V, 460V | ||||||||||||||||||||
Cooling system | Forced air-cooling | ||||||||||||||||||||
Weight (Kg) |
9 |
9 |
14 |
14 |
14 |
20 |
25 |
25 |
26 |
40 |
46 |
50 |
65 |
70 |
70 |
93 |
123 |
123 |
123 |
123 |
123 |
370KW and above on request only
C. Standard specification
Control method | Sine P.W.M control | |
Frequency accuracy | Digital setting: ±0.1% Analog setting: ±0.5% (35℃) | |
Frequency resolution | Digital setting: 0.5~100Hz→0.01Hz 100Hz~240Hz→0.1Hz Analog setting: (setting value/1024)Hz |
|
Frequency range | 0.5~240HZ(Initial frequency 0.5~30Hz) | |
V/F ratio | 10 patterns, or any V/F patterns. | |
Torque boost | 0~15.0% voltage boost, automatic voltage boost | |
Accel. / Decel. time | 0.1~6000 sec(linear, two-step setting) | |
Motor Braking | 100% DB. Under 3.7KW Including braking resister. | 20% DB. Connect extra braking resister to reach 100% DB. |
DC Braking | DC Injection Braking(Setting mode, torque, time, active frequency) | |
Standard feature | Free run restart, jogging speed, upper/lower frequency limit setting, jump frequency setting, 8-step speed setting, frequency increase/decrease (UP/DOWN) function, BIAS, frequency indicated output (DC0~10V), operation direction setting, forward/reverse prohibit, voltage/current limit, data lock, multi-step function, auto record when power off, 6 memory pattern of multi-step function. | |
Frequency setting | Digital setting by keypad, or external analog signal(DC0~10V, DC4~20mA) | |
Display | 7-segment LED display: Frequency, current, voltage, setting value, function, fault status, Temperature of PIM module, status of multi-step function, average speed of multi-step function, instant power, power factor, Kwh, Mwh. | |
Protection | Low voltage, over voltage, instantaneous power failure, over voltage stall, overload, over current stall, instantaneous over current, acceleration over current, deceleration over current, over heat. | |
Overload capacity | 150% for 1 min, anti-time limit function, adjustable ( 25~100﹪) | |
Altitude | Altitude 1,000m or lower, keep from corrosive gasses, liquid and dust | |
Ambient Temperature | -10℃~50℃ (Non-condensing and not frozen) | |
Vibration | Below 0.6G | |
Humidity | Relative between 45﹪ to 90% (No condensing) |
Output Frequency 0.5~400.0Hz
PWN frequency 2~12KHz
9-step speed setting
Parameter input by key number 0~9
15 pattern and any V/F pattern
Speed command PID loop for system application
Provide high DPI A/D 14Bits, A/D 12Bits
Built-in ENCODER feedback interface
External analog setting ±10V, 0~10V and 4~20mA
Built-in standard RS422/485 communication port, MODBUS RTU protocol
V/F open/close loop control, Vector control, Vector close loop control, Torque control
Motor Parameter autotuning, automatic voltage compensation and slip compensation
Control Performance upgraded by adding encoder card, PWN input, analog 12bit ± 10 V input/output, CAN BUS communication interface
|
Xem thêm tại: Biến tần Cutes CT-2000V
Characteristic
Output frequency 0.5~240.0Hz
External analog setting 0~10V and 4~20mA
Automatic torque compensation and slip compensation
PWN frequency 1.5~10KHz
10 pattern and any V/F pattern
Built-in PI control
Built-in standard RS422/485 communication port, MODBUS RTU protocol
8-step speed setting
Frequency increase/decrease(UP / DOWN)function and 16-step function control setting
Xem chi tiết tại: Biến tần Cutes CT-2000PRO/PRO-i/PLUS
Characteristic
Output Frequency 0.5~400.0Hz
PWN frequency 1.5~15KHz
16-step speed function control setting
16-step external input setting
15 pattern and any V/F pattern
Speed command PID loop for system application
Provide variety encoder card functions
Variety keyboards for option
PWN frequency, external analog setting 12bit±10V and 4~20mA
Built-in standard RS422/485 communication port, MODBUS RTU protocol
V/F open/close loop control, Vector control, Vector close loop control, Torque control
Motor Parameter autotuning, automatic voltage compensation and slip compensation
Characteristic Output Frequency 0.5~400.0Hz PWN frequency 1.5~10KHz 16-step speed function control setting PWN frequency adjustable 1.5~15KHz 15 pattern and any V/F pattern Speed command PID loop for system application Provide variety encoder card functions External analog setting 0~10V and 4~20mA Light loading 120% x 1 min and start torque 150% 16-step external input setting, frequency increase/decrease (UP/DOWN) function Built-in standard RS422/485 communication port, MODBUS RTU protocol V/F open/close loop control, Vector control, Vector close loop control, Torque control Motor Parameter autotuning, automatic voltage compensation and slip compensation